Prevents Pin & Housing Movement For Repeatable Trigger Performance
Eliminates pin drift in the receiver holes so your trigger housing stays in the same place for every shot. Slotted, truss head screws at each end of pin keeps trigger housing properly aligned and free of wobble. Helps deliver reliable trigger performance in tactical and competition guns. Remington includes both front and rear, anti-walk trigger pins.
SPECS: Steel, blued finish. Mossberg - Fits Mossberg 500/590. Winchester - Fits Winchester 1200/1300/1400. Benelli - Fits Benelli Super 90, Winchester Super X and Browning Gold.
Mehr...
Verhindert Bewegung von Stift & Gehäuse für wiederholbare Abzugsleistung
Eliminiert das Abweichen der Stifte in den Empfängerbohrungen, sodass dein Abzuggehäuse bei jedem Schuss an der gleichen Stelle bleibt. Mit Schlitz- und Trusskopfschrauben an jedem Ende des Stifts bleibt das Abzuggehäuse richtig ausgerichtet und wackelfrei. Hilft, eine zuverlässige Abzugsleistung bei taktischen und Wettkampfwaffen zu gewährleisten. Remington umfasst sowohl vordere als auch hintere, anti-walk Abzugsstifte.
SPECS: Stahl, blauer Finish. Mossberg - Passt für Mossberg 500/590. Winchester - Passt für Winchester 1200/1300/1400. Benelli - Passt für Benelli Super 90, Winchester Super X und Browning Gold.
Mehr...
Kundenbewertungen zu BROWNELLS MOSSBERG ANTI-WALK TRIGGER HOUSING PIN
Anzahl der Bewertungen: 11
Von brownells.com: 11
Durchschnittliche Bewertung: 2,8
Decent little upgrade(14.02.2014)
I used the Benelli version of this pin in an American Tactical Imports TAC-SX2 shotgun. It fits it perfectly. It came a little dirty, so I used some CLP to clean it up. 4 stars instead of 5 because the included slot head screws are trash. Brownells should consider including some better quality Torx or socket head screws with these instead. It's threaded for 6-32 screws, in case you want to change them out.
Not worth it(04.03.2013)
Requires quite a bit of material to be removed from the ends of the pin, screw then removing a bunch of material from the screw threads so it'll screw down flush, took me about an hour with a grinder and it's a cut and try kinda proposition. Due to the trigger pin being for the most part retained by the trigger housing it's just not worth it.
Buyer Beware(20.03.2011)
I purchased the anti-walk pin for a Mossberg 500 AT. When I recieved the item it was missing the screws that come with it. A call to customer service and I had replacements in the mail. When I installed the pin it was too long. Even though I have tightened the screws as tight as they go the pin is loose in the reciever. *I would Loc-Tite to prevent the screws working loose.
No screws both times I purchased one(06.06.2011)
I have purchased two of these. Both came without screws. Very disappointed. Not the first time Brownells brand products have been either completely wrong or with things missing.
Good Idea, Poor or NO Qualiaty Control(04.09.2011)
Great product when made correctly. Screws do not fit flush and will snag on everything including your hands. Brownells has been made aware of this problem and fails to correct.
DIY Project(06.04.2012)
I give this product 3 stars not as a trigger housing pin but as a DIY project. The pin is the perfect length but either the screws are too long or the holes in the pin aren't tapped deep enough. It took almost no time to to grind off the screws about 0.1" so they could sit up against the receiver. I think the manufacturer could have done this but if you look at it as a DIY project you won't get too annoyed.
Love this enhancement(01.06.2013)
Mossberg should have made this a factory item. The 500 has a reputation for losing the trigger housing pin. Sure enough, last December squirrel hunting I found the trigger group on the ground with no pin in sight.
Since I had bought the gun the previous May, it was still in warranty. I called Mossberg, and the young lady promised I'd have a replacement pin in the mail. No such thing.
Actually, I'm glad now, because this Brownells pin is a great enhancement. I won't have to worry about the elusive Mossberg pin any more because I KNOW where the Brownells pin is.
The only unusual thing about this pin is the screws need shortening to get it absolutely tight. I don't mind it not being that tight, so I haven't bothered shortening it. I may later.
Perfect for 590(25.10.2014)
Fit perfectly without modification. Trigger assembly will not ever fall out again. Any fitment issues must have been addressed by Brownells after earlier reviews. Screw heads are flush against receiver, and do not snag clothing, etc. Very happy 590. Added the metal trigger assembly, and fresh magazine spring for completeness.
Perfect fit and function(22.07.2009)
I use these in all shotguns I build or modify for customers. A big improvement over the factory pins. No movement with high round counts. Withstands recoil to keep your trigger group in the same place shot after shot. Button head allen screws would not only look much better but minimize risk with slotted screw drivers.
Good idea(05.08.2011)
These pins require slotted screwdrivers and as said in the other review Allen screws would be preferable. While installing the pins on a bench with a gun vise my screw driver slipped and and took a small piece out of the side of the screw head. Making it hard to finish the install. I have a picatinny rail mount that uses the same holes as these pins (the bolts supplied with it are allen head). I decided to reinstall the rail and try to get my money back. I will purchase these again if they are modified to allen heads.
Guarantee "Peace of mind"(30.09.2012)
Does exactly what it describes. Replaces trigger pins with these anti-walk trigger pins. So now when stumbling around in the bush one will not lose a pin.
I've upgraded every Remington 870, Mossberg 500 & 835 I've ever owned with the appropriate trigger pins.
Artikel-Nr.: 078000049 BROWNELLS MOSSBERG ANTI-WALK TRIGGER HOUSING PIN Eliminiert das Abweichen der Stifte in den Empfängerbohrungen, sodass dein Abzuggehäuse bei jedem Schuss an der gleichen Stelle bleibt. Mit Schlitz- und Trusskopfschrauben an jedem Ende des Stifts bleibt das Abzuggehäuse richtig ausgerichtet und wackelfrei. Hilft, eine zuverlässige Abzugsleistung bei taktischen und Wettkampfwaffen zu gewährleisten. Remington umfasst sowohl vordere als auch hintere, anti-walk Abzugsstifte.
Artikel-Nr.: 078000050 BROWNELLS WINCHESTER ANTI-WALK TRIGGER HOUSING PIN Eliminiert das Abweichen der Stifte in den Empfängerbohrungen, sodass dein Abzuggehäuse bei jedem Schuss an der gleichen Stelle bleibt. Mit Schlitz- und Trusskopfschrauben an jedem Ende des Stifts bleibt das Abzuggehäuse richtig ausgerichtet und wackelfrei. Hilft, eine zuverlässige Abzugsleistung bei taktischen und Wettkampfwaffen zu gewährleisten. Remington umfasst sowohl vordere als auch hintere, anti-walk Abzugsstifte.
Artikel-Nr.: 078000051 BROWNELLS BENELLI ANTI-WALK TRIGGER HOUSING PIN Eliminiert das Abweichen der Stifte in den Empfängerbohrungen, sodass dein Abzuggehäuse bei jedem Schuss an der gleichen Stelle bleibt. Mit Schlitz- und Trusskopfschrauben an jedem Ende des Stifts bleibt das Abzuggehäuse richtig ausgerichtet und wackelfrei. Hilft, eine zuverlässige Abzugsleistung bei taktischen und Wettkampfwaffen zu gewährleisten. Remington umfasst sowohl vordere als auch hintere, anti-walk Abzugsstifte.
Artikel-Nr.: 078000057 BROWNELLS ANTI-WALK TRIGGER HOUSING PIN REPLACEMENT SCREWS PAIR Eliminiert das Abweichen der Stifte in den Empfängerbohrungen, sodass dein Abzuggehäuse bei jedem Schuss an der gleichen Stelle bleibt. Mit Schlitz- und Trusskopfschrauben an jedem Ende des Stifts bleibt das Abzuggehäuse richtig ausgerichtet und wackelfrei. Hilft, eine zuverlässige Abzugsleistung bei taktischen und Wettkampfwaffen zu gewährleisten. Remington umfasst sowohl vordere als auch hintere, anti-walk Abzugsstifte.
Prevents Pin & Housing Movement For Repeatable Trigger Performance
Eliminates pin drift in the receiver holes so your trigger housing stays in the same place for every shot. Slotted, truss head screws at each end of pin keeps trigger housing properly aligned and free of wobble. Helps deliver reliable trigger performance in tactical and competition guns. Remington includes both front and rear, anti-walk trigger pins.
SPECS: Steel, blued finish. Mossberg - Fits Mossberg 500/590. Winchester - Fits Winchester 1200/1300/1400. Benelli - Fits Benelli Super 90, Winchester Super X and Browning Gold.
Mehr...
Verhindert Bewegung von Stift & Gehäuse für wiederholbare Abzugsleistung
Eliminiert das Abweichen der Stifte in den Empfängerbohrungen, sodass dein Abzuggehäuse bei jedem Schuss an der gleichen Stelle bleibt. Mit Schlitz- und Trusskopfschrauben an jedem Ende des Stifts bleibt das Abzuggehäuse richtig ausgerichtet und wackelfrei. Hilft, eine zuverlässige Abzugsleistung bei taktischen und Wettkampfwaffen zu gewährleisten. Remington umfasst sowohl vordere als auch hintere, anti-walk Abzugsstifte.
SPECS: Stahl, blauer Finish. Mossberg - Passt für Mossberg 500/590. Winchester - Passt für Winchester 1200/1300/1400. Benelli - Passt für Benelli Super 90, Winchester Super X und Browning Gold.
Mehr...
Kundenbewertungen zu BROWNELLS MOSSBERG ANTI-WALK TRIGGER HOUSING PIN
Anzahl der Bewertungen: 11
Von brownells.com: 11
Durchschnittliche Bewertung: 2,8
Decent little upgrade(14.02.2014)
I used the Benelli version of this pin in an American Tactical Imports TAC-SX2 shotgun. It fits it perfectly. It came a little dirty, so I used some CLP to clean it up. 4 stars instead of 5 because the included slot head screws are trash. Brownells should consider including some better quality Torx or socket head screws with these instead. It's threaded for 6-32 screws, in case you want to change them out.
Not worth it(04.03.2013)
Requires quite a bit of material to be removed from the ends of the pin, screw then removing a bunch of material from the screw threads so it'll screw down flush, took me about an hour with a grinder and it's a cut and try kinda proposition. Due to the trigger pin being for the most part retained by the trigger housing it's just not worth it.
Buyer Beware(20.03.2011)
I purchased the anti-walk pin for a Mossberg 500 AT. When I recieved the item it was missing the screws that come with it. A call to customer service and I had replacements in the mail. When I installed the pin it was too long. Even though I have tightened the screws as tight as they go the pin is loose in the reciever. *I would Loc-Tite to prevent the screws working loose.
No screws both times I purchased one(06.06.2011)
I have purchased two of these. Both came without screws. Very disappointed. Not the first time Brownells brand products have been either completely wrong or with things missing.
Good Idea, Poor or NO Qualiaty Control(04.09.2011)
Great product when made correctly. Screws do not fit flush and will snag on everything including your hands. Brownells has been made aware of this problem and fails to correct.
DIY Project(06.04.2012)
I give this product 3 stars not as a trigger housing pin but as a DIY project. The pin is the perfect length but either the screws are too long or the holes in the pin aren't tapped deep enough. It took almost no time to to grind off the screws about 0.1" so they could sit up against the receiver. I think the manufacturer could have done this but if you look at it as a DIY project you won't get too annoyed.
Love this enhancement(01.06.2013)
Mossberg should have made this a factory item. The 500 has a reputation for losing the trigger housing pin. Sure enough, last December squirrel hunting I found the trigger group on the ground with no pin in sight.
Since I had bought the gun the previous May, it was still in warranty. I called Mossberg, and the young lady promised I'd have a replacement pin in the mail. No such thing.
Actually, I'm glad now, because this Brownells pin is a great enhancement. I won't have to worry about the elusive Mossberg pin any more because I KNOW where the Brownells pin is.
The only unusual thing about this pin is the screws need shortening to get it absolutely tight. I don't mind it not being that tight, so I haven't bothered shortening it. I may later.
Perfect for 590(25.10.2014)
Fit perfectly without modification. Trigger assembly will not ever fall out again. Any fitment issues must have been addressed by Brownells after earlier reviews. Screw heads are flush against receiver, and do not snag clothing, etc. Very happy 590. Added the metal trigger assembly, and fresh magazine spring for completeness.
Perfect fit and function(22.07.2009)
I use these in all shotguns I build or modify for customers. A big improvement over the factory pins. No movement with high round counts. Withstands recoil to keep your trigger group in the same place shot after shot. Button head allen screws would not only look much better but minimize risk with slotted screw drivers.
Good idea(05.08.2011)
These pins require slotted screwdrivers and as said in the other review Allen screws would be preferable. While installing the pins on a bench with a gun vise my screw driver slipped and and took a small piece out of the side of the screw head. Making it hard to finish the install. I have a picatinny rail mount that uses the same holes as these pins (the bolts supplied with it are allen head). I decided to reinstall the rail and try to get my money back. I will purchase these again if they are modified to allen heads.
Guarantee "Peace of mind"(30.09.2012)
Does exactly what it describes. Replaces trigger pins with these anti-walk trigger pins. So now when stumbling around in the bush one will not lose a pin.
I've upgraded every Remington 870, Mossberg 500 & 835 I've ever owned with the appropriate trigger pins.