Über 300.000 Kunden - wir sagen Danke!

40,000+ Produkte aus Jagd und Schiesssport

Verbessere die Genauigkeit deines Remington mit der RP Trigger Spring von WOLFF! 🎯 Einfach zu installieren und leistungsstark.

WOLFF REMINGTON 700/721/722 TRIGGER SPRING - WOLFF REM. RP TRIGGER SPRING

969000173

Eigenschaften

  • Modell: 700,721,722
  • Waffentyp: Remington
  • Versandgewicht: 0,005kg
  • Versandhöhe: 10mm
  • Versandbreite: 69mm
  • Versandlänge: 142mm
  • Spezifikationen:
  • Marke: Remington
  • Modell: 700, 721, 722
19.9 19.9 1 EUR
19.9 EUR 19,90 €

Preise inkl. MwSt., zzgl. Versand

Artikel-Nr.: 969000173

Herst.-Nr.: 33240

Gib deinem Remington Repetiergewehr einen Leistungsschub mit diesen einfach zu installierenden Federn. Die reduzierte Kraft (RP) Abzugsfeder hilft, den gefühlten Abzugswiderstand zu senken, was zu besserer und konsistenterer Genauigkeit führt.
Auf Lager
1
2
3
4
5
6
7
8
9
10+
  • Spezifikationen:
  • Marke: Remington
  • Modell: 700, 721, 722

Beschreibung:

Original anzeigen (Englisch)
Abzugswiderstand reduzieren
Gib deinem Remington Repetiergewehr einen Leistungsschub mit diesen einfach zu installierenden Federn. Die reduzierte Kraft (RP) Abzugsfeder hilft, den gefühlten Abzugswiderstand zu senken, was zu besserer und konsistenterer Genauigkeit führt.

TECHNISCHE DATEN: Federstahl. Passt für Rem. 700/721/722.

Eigenschaften

  • Modell: 700,721,722
  • Waffentyp: Remington
  • Versandgewicht: 0,005kg
  • Versandhöhe: 10mm
  • Versandbreite: 69mm
  • Versandlänge: 142mm

Kundenbewertungen

Kundenbewertungen (3)

2 / 5
Nicht empfehlenswert

Brownells USA Junk 23.12.2017

The factory spring allowed minimum of 4 lbs. This spring was shorter and stiffer than the factory spring. 6lbs was as low as you could go before the set screw no longer contacted the spring and the rifle became unsafe. Save time and money and go another route.

Empfehlenswert

Brownells USA Helps a little 26.07.2015

Because Wolff's customer service is not knowledgeable about this product, I ended up going to another company's web site for installation instructions. This spring is NOT the one that goes behind the trigger. DO NOT try to remove the one that goes behind the trigger, and which is tensioned by the screw in the trigger. It goes in the front of the trigger housing assembly. You will need to remove the factory installed sealant to remove the screw that holds this spring in. Also, it is not as long as the one pictured here. It is about 1/3 that length. Trigger pull was reduced to about 3.5 # with this spring installed. That was on a gun that REMINGTON could not (or would not) reduce below 5 #. I sent two NEW rifles back to Remington because of heavy trigger pull. Despite the fact that the hang tag on the brand new guns states, "3 1/2 pounds out of the box" , Remington was unable to actually bring the guns into spec. The guns were returned to me with a heavy trigger pull, and a note explaining that they adjusted to 4.5# and 5.5 #, NOT 3.5. This spring helped, but keep in mind you will need to void the Remington warranty to bring it into Remington spec.

Schon gewusst?

Herstellerinformationen

Verantwortlicher Wirtschaftsakteur gemäß EU-Verordnung

Brownells Austria GmbH
Hauptstraße 13-15
2332 Hennersdorf
Österreich
info@brownells.at

Ups! Da ist etwas schiefgelaufen.

Beim Laden dieses Inhalts ist ein Fehler aufgetreten. Bitte aktualisiere die Seite, um fortzufahren. Wenn das Problem weiterhin besteht, wende dich bitte an unseren Kundenservice.

Zurück nach oben