No-Mar Field Disassembly For Cleaning & Maintenance
Supports the gas cylinder and keeps it from rotating when removing the gas plug. Lets you easily separate these parts at home or in the field, without damage.
Keine Kratzer beim Zerlegen für Reinigung & Wartung
Unterstützt den Gaszylinder und verhindert, dass er sich beim Entfernen des Gasstopfens dreht. Ermöglicht dir, diese Teile ganz einfach zu Hause oder im Feld zu trennen, ohne sie zu beschädigen.
Kundenbewertungen zu FULTON ARMORY M1 GARAND GAS CYLINDER WRENCH
Anzahl der Bewertungen: 7
Von brownells.com: 7
Durchschnittliche Bewertung: 3,9
Just right for the job(03.12.2009)
Perfectly sized for fit, simple tool for a job that in the past I've considered using pliers!
Good tool(27.02.2010)
Works like a champ. Gives you something to hang on to for those tough ones.
This Wrench is Made by People who Use IT(23.06.2010)
Like most things made by Fulton Armory, this wrench has always worked. It does not scratch or mar the finish while using it. My wrench has seen a lot of use and is still going. It has never NOT fit any of the different manufacturer's weapons I own including Armscorp, LRB Arms SA M-14, Low number pre ban Springfield Armory Inc. weapons, as well as new Springfield Armory Inc. weapons.
Needs no modification(18.07.2010)
It does what it says it does without a flaw.
Do not buy for M1A Loaded(22.04.2011)
This did not work on my Loaded M1A. In fact, it wouldn't even fit over the gas cylinder. I am not sure if the loaded models with the National Match barrels on them have a larger gas cylinder or not, but, this was not even close. I did finally get it to fit after some slight modifications with a dremel, but, instead of helping me, it literally just bent out of shape and marred the finish of the rifle. I certainly do not have super-human strength, but, this bent very easily under strain. Beware...
Works on Garand but not my M-14(27.07.2011)
Works fine on my Garand but does not fit my M-14. Material is a bit soft, simply dropping it causes a ding. A simple, cheap tool.
will need a little modification(07.04.2016)
This would not fit a few gas cylinder locks that I have but with a little dressing with fine grit sandpaper, clearance should be ok. My regret is removing the anodizing on the bearing surfaces. Won't affect function, just appearance.
Artikel-Nr.: 100000792 FULTON ARMORY M1 GARAND GAS CYLINDER WRENCH Herstellerproduktnummer: FA-A211-G Unterstützt den Gaszylinder und verhindert, dass er sich beim Entfernen des Gasstopfens dreht. Ermöglicht dir, diese Teile ganz einfach zu Hause oder im Feld zu trennen, ohne sie zu beschädigen.
29.9EUR029,90 €
*
Nachbestellt, Lieferzeit ca. 4-12 Wochen aus dem Lager USA.
No-Mar Field Disassembly For Cleaning & Maintenance
Supports the gas cylinder and keeps it from rotating when removing the gas plug. Lets you easily separate these parts at home or in the field, without damage.
Keine Kratzer beim Zerlegen für Reinigung & Wartung
Unterstützt den Gaszylinder und verhindert, dass er sich beim Entfernen des Gasstopfens dreht. Ermöglicht dir, diese Teile ganz einfach zu Hause oder im Feld zu trennen, ohne sie zu beschädigen.
Kundenbewertungen zu FULTON ARMORY M1 GARAND GAS CYLINDER WRENCH
Anzahl der Bewertungen: 7
Von brownells.com: 7
Durchschnittliche Bewertung: 3,9
Just right for the job(03.12.2009)
Perfectly sized for fit, simple tool for a job that in the past I've considered using pliers!
Good tool(27.02.2010)
Works like a champ. Gives you something to hang on to for those tough ones.
This Wrench is Made by People who Use IT(23.06.2010)
Like most things made by Fulton Armory, this wrench has always worked. It does not scratch or mar the finish while using it. My wrench has seen a lot of use and is still going. It has never NOT fit any of the different manufacturer's weapons I own including Armscorp, LRB Arms SA M-14, Low number pre ban Springfield Armory Inc. weapons, as well as new Springfield Armory Inc. weapons.
Needs no modification(18.07.2010)
It does what it says it does without a flaw.
Do not buy for M1A Loaded(22.04.2011)
This did not work on my Loaded M1A. In fact, it wouldn't even fit over the gas cylinder. I am not sure if the loaded models with the National Match barrels on them have a larger gas cylinder or not, but, this was not even close. I did finally get it to fit after some slight modifications with a dremel, but, instead of helping me, it literally just bent out of shape and marred the finish of the rifle. I certainly do not have super-human strength, but, this bent very easily under strain. Beware...
Works on Garand but not my M-14(27.07.2011)
Works fine on my Garand but does not fit my M-14. Material is a bit soft, simply dropping it causes a ding. A simple, cheap tool.
will need a little modification(07.04.2016)
This would not fit a few gas cylinder locks that I have but with a little dressing with fine grit sandpaper, clearance should be ok. My regret is removing the anodizing on the bearing surfaces. Won't affect function, just appearance.